Parr-instrument 6300 Instrukcja Użytkownika Strona 23
- Strona / 130
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
PROGRAM INSTALLATION & CONTROL
6300
4
www.parrinst.com
23
CHAPTER 4
PROGRAM INSTALLATION &
CONTROL
SOFTWARE INSTALLATION
The program in the 6300 Calorimeter can be extensively
modified to tailor the unit to a wide variety of operating
conditions, reporting units, laboratory techniques,
available accessories and communication modes.
In addition, the calculations, thermochemical
corrections and reporting modes can be modified to
conform to a number of standard test methods and
procedures.
Numerous provisions are included to permit the use of
other reagent concentrations, techniques, combustion
aids and short cuts appropriate for the user’s work.
Note:
Changes to the program are made by use of the menu
structure described in Appendix A of this manual. Any
of these items can be individually entered at any time to
revise the operating program.
DEFAULT SETTINGS
Units are pre programmed with DEFAULT
SETTINGS. See pages 24 and 25 for a listing of the
factory default settings.
These default settings remain in effect until changed
by the user. Should the user ever wish to return to the
factory default settings, go to the Program Information
and Control Menu, then to User/Factory Settings, and
then touch Reload Factory Default Settings and YES.
Non-volatile memory is provided to retain any and
all operator initiated program changes; even if power
is interrupted or the unit is turned off. If the unit
experiences an intentional or unintentional “Cold
Restart”, the controller will return to its default settings.
REVISING DEFAULT SETTINGS
The default parameters of the 6300 Calorimeter can
be changed to guarantee that the 6300 Calorimeter,
when cold restarted, will always be in the desired
configuration before beginning a series of tests.
Users who wish to permanently revise their default
settings may do so using the following procedure:
Establish the operating parameters to be stored as
•
the user default settings.
Go to the Program Info and Control Menu, User/
•
Factory Settings, User Setup ID, and enter the
desired User Setup ID.
Select Save User Default Settings
•
To re-load the user default settings, go to the Program
Info and Control Page, User/Factory Settings, Re-load
User Default Settings, and YES.
- Parr Instrument Company 1
- TABLE OF CONTENTS 3
- PREFACE 7
- EXPLANATION OF SYMBOLS 8
- INTENDED USAGE 8
- CLEANING & MAINTENANCE 8
- SAFETY INFORMATION 8
- GENERAL SPECIFICATIONS 9
- ENVIRONMENTAL CONDITIONS 9
- GETTING STARTED 9
- CONCEPT OF OPERATION 11
- CHAPTER 1 11
- CHAPTER 2 13
- INSTALLATION 13
- WAGELOK TUBE FITTINGS 14
- INSTRUMENT DESCRIPTION 21
- CHAPTER 3 21
- CHAPTER 4 23
- PROGRAM INSTALLATION & 23
- Figure 4-1 24
- Factory Default Settings 25
- Continued 25
- OPERATING INSTRUCTIONS 27
- CHAPTER 5 27
- CHAPTER 6 39
- CORRECTIONS & FINAL 39
- REPORTING INSTRUCTIONS 41
- CHAPTER 7 41
- FILE MANAGEMENT 43
- CHAPTER 8 43
- CHAPTER 9 45
- 500 Tests (Continued) 46
- 5000 Tests 46
- 6300 MAINTENANCE CHECKLIST 47
- BOMB EXHAUST TROUBLESHOOTING 48
- BOMB REMOVAL AND REPLACEMENT 51
- 6300 CALORIMETER ERROR LIST 51
- MENU OPERATING INSTRUCTIONS 53
- APPENDIX A 53
- MENU OPERATING 53
- INSTRUCTIONS 53
- CALCULATIONS 71
- APPENDIX B 71
- STANDARDIZATION 77
- APPENDIX C 77
- COMMUNICATIONS INTERFACES 81
- APPENDIX D 81
- COMMUNICATIONS 81
- INTERFACES 81
- TECHNICAL SERVICE 93
- APPENDIX E 93
- APPENDIX F 95
- PARTS LISTS & DRAWINGS 100
- BOMB RINSE CONTAINER ASSEMBLY 127
- APPENDIX G 127
- BOMB RINSE CONTAINER 127
- ASSEMBLY 127
- Revision 11/5/10 130
Powiązane produkty i podręczniki dla Urządzenia pomiarowe Parr-instrument 6300
(94 strony)Mitsubishi WT-A42 manuals
Owner’s manuals and user’s guides for Projection TVs Mitsubishi WT-A42.
We providing 1 pdf manuals Mitsubishi WT-A42 for download free by document types: Operations Instructions
Komentarze do niniejszej Instrukcji